The Fury II Restoration Project - Page 2 - Mustang Forum

FRED-MATIC · 07-03-2012, 05:13 PM

Progress from the body shop as of today.

Removing all panels for proper prep

The Scot Rod Fab firewall cover is being updated to cover the wiper motor hole. We decided Rain X and the go pedal will work just fine

Bumper covers & wing off

Red, Whte, and perhaps blue hood for patriotism ?

Since were on a diet, off comes the stock bumper mount, & on goes the racing lightweight mount. Goodbye to 25lbs or so of nose weight.

She's coming back to life!

n20capri · 07-05-2012, 05:00 AM

Looking good Fred!

FRED-MATIC · 07-10-2012, 07:25 AM

The body shop work has been progressing quickly. I'm relieved and excited at the mindset of these guys. Being on the same page while undertaking this kind of project makes me sleep better

We decided to pull out the stiff springs, to allow an easier work angle on the front end.

Factory antenna hole was blocked off, with welded plate underneath, and smoothed.

Here you can see the painstaking work of welding, sanding, grinding and filling holes & rough areas of the engine bay.

Upper radiator support is also getting cleaned up

Work on the drivers side, and fender. You would not believe the amount of ripples & dents along the tops of the fenders. NOTE never lean over your Fox fenders without thick blankets.

Rear quarter panels getting smoothed. Also rolled the fender lips properly

Drivers door needed extensive work. Thieves bent up the bottom panel, and busted out the lockset. all new tumblers for doors & trunk

FRED-MATIC · 07-10-2012, 07:29 AM

Passenger side rear lower fender was bent in ( Orange cone excursion I believe) More work on the passenger side

Black Fox · 07-12-2012, 06:04 AM

paint it black

FRED-MATIC · 07-26-2012, 05:34 AM

More progress pictures from the body shop. These guys are doing an incredible job, and are enthusiastic about the project. That's hard to come by these days.

Hood underside painted.

Fenders ready to be squirted

Drivers door opens and closes like new.

Right rear quarter needed quite a bit of work, and huge ding above the fuel door is gone.

The stock rack & pinion BROKE while pushing the car

GEO got a rack and installed it now so we can move the car around again. K member and underside will be cleaned up and repainted too.

Car is scheduled for paint coming up shortly. 8.8 rear end is getting built this week, with all kinds of goodies, so stay tuned.

FRED-MATIC · 07-31-2012, 04:27 AM

While the car is being finalized for paint, Geo tore down the 8.8 housing, and installed the heavy duty goodies.

Donor from 1998 GT

Housing bushings cleaned out

Bushing shrapnel !

Free from the stock Trac-loc and 3:27 cogs, cleaned & awaiting a new cog

Gun owners should .appreciate this. Geo used numerous passes with brake clean soaked rags to insure the inner tubes were free from old lube & contamination. Numerous passes until the rags came through with ZERO dirt.

New bearings

FRED-MATIC · 07-31-2012, 04:33 AM

Looks brand new

Races

A set of 3:55 gears going in, thanks to Chris Jones at BBR for donating a set of take outs.

Ring gear mounted to the Eaton differential, Thank you Jeff from Nitrostang for the great price.

Superior 31 spline axles nestled in

Assembled!

Mounting a T/A Girdle, after the axle tubes get welded up, & paint

FRED-MATIC · 08-04-2012, 04:25 PM

Some teaser pics of initial paintwork. Car got squirted today, so Ill post more Monday

Still loooks wet, but it's dry.

Fenders are arrow straight

95 Bullitt · 08-05-2012, 09:51 AM

Car is coming along great Fred.

I can only imagine what this is doing to your pocket though.

FRED-MATIC · 08-06-2012, 06:30 PM

Paint work is complete! Wetsanding and buffing, and final tweaks commencing this week, then she is back to the shop for wiring and the reconstruction.

MRBiggs · 08-07-2012, 08:54 AM

Is that sounds deadner in the middle of the hood or just the bare fiberglass?

Looks fookin specatcular thus far man.

FRED-MATIC · 08-07-2012, 09:31 AM

Quote:

Originally Posted by MRBiggs

Is that sounds deadner in the middle of the hood or just the bare fiberglass?

Looks fookin specatcular thus far man.

Its the fiberglass. We decided to paint it black, to offset all the white, and to hide dirt chips etc.

MRBiggs · 08-07-2012, 11:28 AM

Quote:

Originally Posted by FRED-MATIC

Its the fiberglass. We decided to paint it black, to offset all the white, and to hide dirt chips etc.

I like that look... I was thinking of something similar when I paint my Cervini hood just to hide any dirt that may come up.

FRED-MATIC · 08-07-2012, 11:44 AM

Forgot one

FRED-MATIC · 08-14-2012, 04:05 AM

Paint work and wetsanding/buffing is now complete. She's back in GEO's shop awaitng reconstruction. Wiring will commence soon, with interior restoration to follow.
The pictures just do not do the workmanship justice. Quote, It's CRYSTAL CLEAR!

Ride back from the body shop

Back to the operating room

Alright, wheels gotta go

True Forged Mach 5's may be in the future, like these

Engine bay the way it should be, without the swiss cheese look

Tucked away

FRED-MATIC · 10-05-2012, 04:17 AM

Pictures coming this weekend. Wiring process and battery box installed

n20capri · 10-05-2012, 04:32 AM

Looking good Fred! Can't wait to see new pics!

FRED-MATIC · 10-11-2012, 05:24 AM

Lots of progress since coming back from paint. The painstaking process of re-wiring and modifiying the entire cars electronic wiring is nearly complete.

A new windshield was in order, so we took care of that.

SCRATCH THE PAINT AND I WILL KILL YOU!!

Remote shut off

Sneak peek of under fender wiring

Lights

Behind front bumper

Battery Box

Molding prep & finish work

FRED-MATIC · 10-11-2012, 05:25 AM

Old, dingy, and faded.

Prepped and squirted

Although the quarter windows were redone, we wanted all trim to match perfectly

Special glue flown in from the LaBrea tar pits

Coming together!

99GT281 · 10-11-2012, 05:53 AM

you spraypaint very nicely

Damouth · 10-11-2012, 08:16 AM

Did all that trim just pop off pretty easily? i need to do the saem thing to mine and that looks fairly inexpensive

FRED-MATIC · 10-11-2012, 09:12 AM

Quote:

Originally Posted by Damouth

Did all that trim just pop off pretty easily? i need to do the saem thing to mine and that looks fairly inexpensive

Removal, restoring, and re installing is a bit of an art form, since you have to be extremely careful not to bend them, or break the clips .

Also, trial and error has found the CORRECT paint that provides a factory finish, without excessive gloss, yet holds up years longer than O.E.

MRBiggs · 10-11-2012, 09:52 PM

Looks great. Fresh trim goes SO far in making the car come together.
I did the cowl, mirrors and top well trim on my car a while back and it instantly updates the whole car.

FRED-MATIC · 10-16-2012, 04:33 AM

More work on restoring the window moldings and trim pieces.

Tore off the old back window tint, and removed the old glue ( about as much fun as a trip to the dentist!) Also clay bar treated the inside and out, which removed years of hard water spots and debris.

Passenger side process was the same as previous, however we decided the inner portion of the B pillar needed some TLC in black.

Done. Drivers side got the same treatment shortly after

Quarter window

Some salvage yard serching rewarded us with door hrnesses, a complete steering column, and a couple of other goodies. Spare steeering wheel is being sent out for restoration & wrap.

The next point goes for ANYONE who has ever rewired a car, this is like Frankenstein coming to life.
WE HAVE POWER!!!!

331 LX · 10-16-2012, 10:18 AM

Quote:

Originally Posted by MRBiggs

Looks great. Fresh trim goes SO far in making the car come together.
I did the cowl, mirrors and top well trim on my car a while back and it instantly updates the whole car.

Truth.

I bought all new trim and did the qtr windows on the fox. Mine were in rough shape, and it was a pain getting the 1/4's out. So happy with the trim though, it makes a huge difference.

Looks great Fred.

modo · 10-16-2012, 10:49 AM

what did you use for trim paint?

car is looking great

331 LX · 10-16-2012, 12:20 PM

Quote:

Originally Posted by modo

what did you use for trim paint?

car is looking great

We used a 3m trim paint on pops old Mercedes... I'll take a pic of it tonight for ya. It came out amazing.

MRBiggs · 10-16-2012, 10:55 PM

I used Duplicolor trim paint... comes in a spray can. **** came out spectacular. I been using it on most anything I want black now. Even used it to black out the chrome window trims on my Pontiac G8. Came out tits and you really cant beat it for 6 bucks a can.
Here's my mirror...

FRED-MATIC · 10-31-2012, 05:08 AM

The trim work is about 90% complete. We may replace the door belt moldings, or try a different base coat/top coat methond, ans the originals were in pretty rough shape.
New door lock actuators, lock cylinders, and door handles installed. The factory pop rivets them in, but this method can lead to the handle contacting the door skin. We bolted them in instead. Straight and clean.

Finished. Also LRS hooked us up with all new door seals, run channels, and weatherstripping. Doors work better than NEW!

Tailight assemblies got buffed and polished
BEFORE

AFTER

After some thought, we dcided to shoot the license plate and tailight panel in black.

Quick hand drawn vanity plate! THE FURY II

Now to the Headlights. Long story short, the hardware assemblies needed some modifications and drilling, but GEO got everything in, weather sealed, and better than new.

Had to drill for proper depth and diameter

Still some aligning to do, but after the headlight bulbs come in.

MRBiggs · 11-01-2012, 11:16 PM

Great progress man! Nothing like crisp white paint with fresh, super clean black trim. Love it.

FRED-MATIC · 11-02-2012, 04:15 AM

Quote:

Originally Posted by MRBiggs

Great progress man! Nothing like crisp white paint with fresh, super clean black trim. Love it.

Gonna have to hit you up for some 3 inch Dr Gas X pipe pieces for LT's.

FRED-MATIC · 11-02-2012, 04:30 AM

Time to overhaul the HVAC system. Out comes the heater box/blower motor assembly
Out of the dash

The behemoth

New vs Old

Installed

We were talking door handles. OE are riveted on, and you can see here how this method puts the handle too close to the door skin, leading to contact. GEO installed the new set with bolts.

Coming off

The right way

Drivers door finished

FRED-MATIC · 11-02-2012, 04:41 AM

Time to overhaul the HVAC system. Out comes the heater box/blower motor assembly
Out of the dash

The behemoth

New vs Old

Installed

We were talking door handles. OE are riveted on, and you can see here how this method puts the handle too close to the door skin, leading to contact. GEO installed the new set with bolts.

Coming off

The right way

Drivers door finished

MRBiggs · 11-02-2012, 03:54 PM

Quote:

Originally Posted by FRED-MATIC

Gonna have to hit you up for some 3 inch Dr Gas X pipe pieces for LT's.

I'd have been honored to help you out with that too... but sadly Dr Gas is no more. Closed shop about 6 months ago....

Guess I should change my sig.

07-03-2012, 05:13 PM	#41
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Progress from the body shop as of today. Removing all panels for proper prep The Scot Rod Fab firewall cover is being updated to cover the wiper motor hole. We decided Rain X and the go pedal will work just fine Bumper covers & wing off Red, Whte, and perhaps blue hood for patriotism ? Since were on a diet, off comes the stock bumper mount, & on goes the racing lightweight mount. Goodbye to 25lbs or so of nose weight. She's coming back to life! __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:09 AM.

07-05-2012, 05:00 AM	#42
n20capri AscMcLaren Capri #26/115 Join Date: Sep 2002 Location: Bensalem, PA Posts: 3,611	Looking good Fred! __________________ Mike 86 AscMcLaren Capri #026/114 \| 11.2@123 86 Mustang SVO \|14.0@97 \| 19psi My Website 79-86 Dash Pad Repair Tech S-Box Install Tech Custom center caps, vinyl decals racing #'s etc www.baldguydesigns.net Want your car on a T-shirt? - CLICKY CLICKY

07-10-2012, 07:25 AM	#43
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	The body shop work has been progressing quickly. I'm relieved and excited at the mindset of these guys. Being on the same page while undertaking this kind of project makes me sleep better We decided to pull out the stiff springs, to allow an easier work angle on the front end. Factory antenna hole was blocked off, with welded plate underneath, and smoothed. Here you can see the painstaking work of welding, sanding, grinding and filling holes & rough areas of the engine bay. Upper radiator support is also getting cleaned up Work on the drivers side, and fender. You would not believe the amount of ripples & dents along the tops of the fenders. NOTE never lean over your Fox fenders without thick blankets. Rear quarter panels getting smoothed. Also rolled the fender lips properly Drivers door needed extensive work. Thieves bent up the bottom panel, and busted out the lockset. all new tumblers for doors & trunk __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:10 AM.

07-10-2012, 07:29 AM	#44
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Passenger side rear lower fender was bent in ( Orange cone excursion I believe) More work on the passenger side __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:11 AM.

07-26-2012, 05:34 AM	#46
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	More progress pictures from the body shop. These guys are doing an incredible job, and are enthusiastic about the project. That's hard to come by these days. Hood underside painted. Fenders ready to be squirted Drivers door opens and closes like new. Right rear quarter needed quite a bit of work, and huge ding above the fuel door is gone. The stock rack & pinion BROKE while pushing the car GEO got a rack and installed it now so we can move the car around again. K member and underside will be cleaned up and repainted too. Car is scheduled for paint coming up shortly. 8.8 rear end is getting built this week, with all kinds of goodies, so stay tuned. __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:12 AM.

07-12-2012, 06:04 AM	#45
Black Fox Registered User Join Date: Nov 2002 Posts: 47,267	paint it black

07-31-2012, 04:27 AM	#47
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	While the car is being finalized for paint, Geo tore down the 8.8 housing, and installed the heavy duty goodies. Donor from 1998 GT Housing bushings cleaned out Bushing shrapnel ! Free from the stock Trac-loc and 3:27 cogs, cleaned & awaiting a new cog Gun owners should .appreciate this. Geo used numerous passes with brake clean soaked rags to insure the inner tubes were free from old lube & contamination. Numerous passes until the rags came through with ZERO dirt. New bearings __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:13 AM.

07-31-2012, 04:33 AM	#48
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Looks brand new Races A set of 3:55 gears going in, thanks to Chris Jones at BBR for donating a set of take outs. Ring gear mounted to the Eaton differential, Thank you Jeff from Nitrostang for the great price. Superior 31 spline axles nestled in Assembled! Mounting a T/A Girdle, after the axle tubes get welded up, & paint __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:14 AM.

08-04-2012, 04:25 PM	#49
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Some teaser pics of initial paintwork. Car got squirted today, so Ill post more Monday Still loooks wet, but it's dry. Fenders are arrow straight __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:14 AM.

08-06-2012, 06:30 PM	#51
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Paint work is complete! Wetsanding and buffing, and final tweaks commencing this week, then she is back to the shop for wiring and the reconstruction. __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:15 AM.

08-07-2012, 08:54 AM	#52
MRBiggs Stroked Oinker Join Date: Apr 2001 Location: La Verne, So. Cal Posts: 7,352	Is that sounds deadner in the middle of the hood or just the bare fiberglass? Looks fookin specatcular thus far man. __________________ Current Project: 95 GT Vert 347 w/ TFS R intake\|Windsor Srs head\|Rawls custom cam\|LTs\| ?/? rwhp/tq FORMER Dr. Gas X pipe / Spintech Muffler Distributor WWW.SOCALHORSEPOWER.COM Rio Red 95 Cobra w/ Rotrex blown 302

08-07-2012, 11:44 AM	#55
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Forgot one __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481

08-14-2012, 04:05 AM	#56
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Paint work and wetsanding/buffing is now complete. She's back in GEO's shop awaitng reconstruction. Wiring will commence soon, with interior restoration to follow. The pictures just do not do the workmanship justice. Quote, It's CRYSTAL CLEAR! Ride back from the body shop Back to the operating room Alright, wheels gotta go True Forged Mach 5's may be in the future, like these Engine bay the way it should be, without the swiss cheese look Tucked away __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-05-2012 at 04:16 AM.

10-05-2012, 04:17 AM	#57
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Pictures coming this weekend. Wiring process and battery box installed __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481

10-05-2012, 04:32 AM	#58
n20capri AscMcLaren Capri #26/115 Join Date: Sep 2002 Location: Bensalem, PA Posts: 3,611	Looking good Fred! Can't wait to see new pics! __________________ Mike 86 AscMcLaren Capri #026/114 \| 11.2@123 86 Mustang SVO \|14.0@97 \| 19psi My Website 79-86 Dash Pad Repair Tech S-Box Install Tech Custom center caps, vinyl decals racing #'s etc www.baldguydesigns.net Want your car on a T-shirt? - CLICKY CLICKY

10-11-2012, 05:24 AM	#59
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Lots of progress since coming back from paint. The painstaking process of re-wiring and modifiying the entire cars electronic wiring is nearly complete. A new windshield was in order, so we took care of that. SCRATCH THE PAINT AND I WILL KILL YOU!! Remote shut off Sneak peek of under fender wiring Lights Behind front bumper Battery Box Molding prep & finish work __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-25-2012 at 03:19 AM.

10-11-2012, 05:25 AM	#60
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Old, dingy, and faded. Prepped and squirted Although the quarter windows were redone, we wanted all trim to match perfectly Special glue flown in from the LaBrea tar pits Coming together! __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-25-2012 at 03:23 AM.

10-11-2012, 05:53 AM	#61
99GT281 8 Ribbed and Cammed Join Date: Jun 2003 Location: Floor-It-Duh Posts: 51,713	you spraypaint very nicely __________________

10-11-2012, 08:16 AM	#62
Damouth Registered User Join Date: Nov 2005 Location: Roanoke, VA Posts: 175	Did all that trim just pop off pretty easily? i need to do the saem thing to mine and that looks fairly inexpensive

10-11-2012, 09:52 PM	#64
MRBiggs Stroked Oinker Join Date: Apr 2001 Location: La Verne, So. Cal Posts: 7,352	Looks great. Fresh trim goes SO far in making the car come together. I did the cowl, mirrors and top well trim on my car a while back and it instantly updates the whole car. __________________ Current Project: 95 GT Vert 347 w/ TFS R intake\|Windsor Srs head\|Rawls custom cam\|LTs\| ?/? rwhp/tq FORMER Dr. Gas X pipe / Spintech Muffler Distributor WWW.SOCALHORSEPOWER.COM Rio Red 95 Cobra w/ Rotrex blown 302

10-16-2012, 04:33 AM	#65
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	More work on restoring the window moldings and trim pieces. Tore off the old back window tint, and removed the old glue ( about as much fun as a trip to the dentist!) Also clay bar treated the inside and out, which removed years of hard water spots and debris. Passenger side process was the same as previous, however we decided the inner portion of the B pillar needed some TLC in black. Done. Drivers side got the same treatment shortly after Quarter window Some salvage yard serching rewarded us with door hrnesses, a complete steering column, and a couple of other goodies. Spare steeering wheel is being sent out for restoration & wrap. The next point goes for ANYONE who has ever rewired a car, this is like Frankenstein coming to life. WE HAVE POWER!!!! __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481 Last edited by FRED-MATIC; 10-16-2012 at 04:37 AM.

10-16-2012, 10:49 AM	#67
modo That Guy Join Date: Jan 2002 Location: In a house Posts: 9,804	what did you use for trim paint? car is looking great __________________ 93 GT 66 Coupe

10-16-2012, 10:55 PM	#69
MRBiggs Stroked Oinker Join Date: Apr 2001 Location: La Verne, So. Cal Posts: 7,352	I used Duplicolor trim paint... comes in a spray can. ** came out spectacular. I been using it on most anything I want black now. Even used it to black out the chrome window trims on my Pontiac G8. Came out tits and you really cant beat it for 6 bucks a can. Here's my mirror... __________________ Current Project: 95 GT Vert 347 w/ TFS R intake\|Windsor Srs head\|Rawls custom cam\|LTs\| ?/? rwhp/tq FORMER Dr. Gas X pipe / Spintech Muffler Distributor** WWW.SOCALHORSEPOWER.COM Rio Red 95 Cobra w/ Rotrex blown 302

10-31-2012, 05:08 AM	#70
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	The trim work is about 90% complete. We may replace the door belt moldings, or try a different base coat/top coat methond, ans the originals were in pretty rough shape. New door lock actuators, lock cylinders, and door handles installed. The factory pop rivets them in, but this method can lead to the handle contacting the door skin. We bolted them in instead. Straight and clean. Finished. Also LRS hooked us up with all new door seals, run channels, and weatherstripping. Doors work better than NEW! Tailight assemblies got buffed and polished BEFORE AFTER After some thought, we dcided to shoot the license plate and tailight panel in black. Quick hand drawn vanity plate! THE FURY II Now to the Headlights. Long story short, the hardware assemblies needed some modifications and drilling, but GEO got everything in, weather sealed, and better than new. Had to drill for proper depth and diameter Still some aligning to do, but after the headlight bulbs come in. __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481

11-01-2012, 11:16 PM	#71
MRBiggs Stroked Oinker Join Date: Apr 2001 Location: La Verne, So. Cal Posts: 7,352	Great progress man! Nothing like crisp white paint with fresh, super clean black trim. Love it. __________________ Current Project: 95 GT Vert 347 w/ TFS R intake\|Windsor Srs head\|Rawls custom cam\|LTs\| ?/? rwhp/tq FORMER Dr. Gas X pipe / Spintech Muffler Distributor WWW.SOCALHORSEPOWER.COM Rio Red 95 Cobra w/ Rotrex blown 302

11-02-2012, 04:30 AM	#73
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Time to overhaul the HVAC system. Out comes the heater box/blower motor assembly Out of the dash The behemoth New vs Old Installed We were talking door handles. OE are riveted on, and you can see here how this method puts the handle too close to the door skin, leading to contact. GEO installed the new set with bolts. Coming off The right way Drivers door finished __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481

11-02-2012, 04:41 AM	#74
FRED-MATIC Charles Bronson Join Date: Dec 2003 Location: Palm Coast FL Posts: 6,774	Time to overhaul the HVAC system. Out comes the heater box/blower motor assembly Out of the dash The behemoth New vs Old Installed We were talking door handles. OE are riveted on, and you can see here how this method puts the handle too close to the door skin, leading to contact. GEO installed the new set with bolts. Coming off The right way Drivers door finished __________________ Ship Your Car Now Senior VP of Enterprise Sales 561-705-0481